Getting Hands-On-Rolling Up Your Sleeves-Digging In with Your Own-DIY-Personal Shower Drain-Bathroom Drain-Drainage System Installation-Setup-Project

Get An Estimate

How do you actually feel when it comes to How to Install or Replace a Shower Drain?


How to Install or Replace a Shower Drain
Upgrading a washroom is one of the extra prominent home enhancement tasks. Dealing with the plumbing for draining your shower can be exceptionally easy unless you overdo.

Handling Your Own Shower Drain Installment Project



Whether you are a tub or shower individual, the majority of people look for shower only choices when acquiring a home. This easy reality means more than a few house owners invest a weekend upgrading or setting up showers in their shower rooms. Fortunately for you, it is a fairly basic procedure.

An enthusiast or pan refers to the horizontal surface located at the end of the shower. The enthusiast commonly contains a non-slip surface slightly banked towards the facility or wherever the drain is located. Combined with 3 to 4 inch wall surfaces around the side, the objective of your shower drainage plumbing is to get the water to flow to and down the drain.

You can physically build a collector for your new shower, however you truly need to think about it. Do you really want to enter into the problems of getting the sloping correct, not to mention making sure every aspect of it is waterproof? And also I indicate every element! It is much easier to simply buy a pre-cast enthusiast online or at your regional Lowes, House Depot or equipment shop. Building one might sound like a great suggestion, however you will most likely feel differently after a couple of hours.

Regardless of just how you set about getting a pan, you need to strive to utilize one that has the drain situated in the exact same spot as the original frying pan. Moving the drain pipelines can be a task, particularly if the building contractor utilized a distinct framework framework. If you are identified to relocate the drainpipe, you are going to need to cut down the pipe or extend it, which may suggest destroying large portions of the floor. Put another way, you are mosting likely to be taking a look at a multiple weekend break project.

Thinking we have our drain aligned, the actual hook up is relatively simple. The drainage pipeline should be encountering vertical approximately the collection agency. It will certainly typically resemble a "U", which indicates it acts as a cleanout to keep unpleasant smells from returning up from the drain. To attach the drain, you are mosting likely to create a water limited connection between a drainpipe cap on the top of the pan and also the drainage pipeline. Systems vary, yet you are commonly mosting likely to do this by putting a combining piece on the top of the drain pipeline. This is then covered with gaskets and also literally screwed into the drainpipe cap. The drain cap ought to work as a locknut, to wit, it screws straight onto the coupling.

The difficult part of this procedure is getting your drain cap to match a watertight setting in the frying pan. This is accomplished by backing off the drainpipe cap as soon as you are sure whatever meshes. Then, you placed plumbings putty around the bottom of the cap and after that screw it back on. The putty needs to create a limited seal between the cap and the shower pan, which maintains water from flowing under it and also into the mounting under the shower.

Clearly, washroom showers come in a wide variety of styles these days. If you buy a collection agency, they almost always featured plumbing instructions or the store can note anything unusual you ought to understand. It appears intricate, yet is commonly rather simple. Have a good time!

How To Install & Replace A Shower Drain In 5 Steps


Replacing a shower drain, or installing one for the first time, often requires a plumber, but if you’re confident in your DIY skills then you may be able to do it yourself. Your new shower drain should come with specific installation instructions, so take time to familiarise yourself with those before you get started. There are several types of shower drain, and the one you choose or are supplied with will depend on your shower tray, your pipes and the manufacturer’s recommendations. All Mira shower trays are compatible with compression-style shower drains, which attach to your home’s drainpipes with compression washers and nuts. Here’s an overview of how to install this type of drain.


How to install a compression-style drain


Please bear in mind that these are general instructions, and you should refer to the manufacturer’s recommendations to install your shower drain.


Trim the drainpipe


The drainpipe should come up to 2cm below the lip of the shower drain. You might need to lift the shower base on to mark the right height, and then remove it again before trimming the drainpipe with a hacksaw. Ensure the cut is flat and level.


Attach the drain assembly to the shower base


Apply silicone caulk to the lower rim of the drain assembly and insert it into the shower base from the top side of the base. This should be done before the base is put in place on the floor. Press the drain assembly firmly into place so that the caulk forms an even seal.



Slide the rubber washer and slip washer on to the drain assembly from underneath the shower base, then thread the drain nut on and tighten it with pliers.



Wipe away any excess caulk that has oozed out.


Put the shower base in position


Carefully position the shower base so that the drain assembly lines up with the drainpipe and fits inside it. It’s a good idea to get someone else to help out, and it’s usually easier to set the back of the base down first, and then lower the front of the base down.


Insert the compression gasket and nut


Slide the rubber compression gasket down into the drain opening so that it fits around the drainpipe. The top of the gasket should line up with the top of the pipe, or be slightly lower.



Drop the compression nut into the drain opening and use the fitting tool that will likely have been provided and a screwdriver to tighten the nut. As you tighten it, the gasket will be compressed against the drainpipe, creating a watertight seal.


Fit the metal strainer


Press the metal strainer into the drain opening, making sure the top surface is lower than the shower floor around it.



And there you have it, a brand-new shower drain! Allow the silicone to set for a full 24 hours before using the shower.


Cleaning and maintenance of your shower drain


Shower drains can quickly become clogged with hair and a build-up of product, which can lead to bad smells and can prevent your shower water from draining efficiently.



To maintain your shower drain, clear out any strands of hair that gather on the metal strainer after each shower. We recommend cleaning your shower drain thoroughly once a month using boiling water to loosen up soap scum and get things moving.

https://www.mirashowers.co.uk/blog/how-to/how-to-install-replace-a-shower-drain-in-5-steps/


How to Install a Shower Drain in a Basement

We had been made aware of that report on How to Choose the Best Drain for Your Shower from someone on our other blog. Be sure to take the opportunity to distribute this blog post if you enjoyed it. Thank you so much for your time invested reading it.

Leave a Reply

Your email address will not be published. Required fields are marked *